# |
Part Name (Click to view) |
BOM
Qty |
1 | Weldment frame 600T | 1 |
2 | Foot, Leveler | 2 |
3 | Deck Spring | 2 |
4 | Screw | 2 |
5 | Stiffener - Deck | 2 |
6 | Tape strip 1.20 X 39.45 X .01 | 2 |
7 | Tape strip 1.20x6.00x.01 | 2 |
8 | Cover, Side | 2 |
9 | NLA End cap right 600T | 1 |
10 | NLA Endcap, Rear, Left | 1 |
11 | Screw | 5 |
12 | NLA Deck | 1 |
13 | Treadbelt, Logo | 1 |
14 | Disk Guide Deck Edge | 2 |
15 | Washer, Flat | 8 |
16 | Wshr Lock Ex 5-16 Zinc | 13 |
17 | Bolt 5/16-18X1/62 HXHD G5 zinc | 10 |
18 | NLA Roller, Rear | 1 |
19 | Bushing Nylon 1-2In.Nf810-5-0 | 2 |
20 | Nut 1-2-13 Hex Stl Zinc | 2 |
21 | Wshr B 1-2 Narrow Zinc | 4 |
22 | Spring 1In. O.D.360 Max Ld. | 2 |
23 | Thrust Brg 1-2In. No. Tb812 | 2 |
24 | Bolt 1/2-13x6LG HEX HD GR5 | 2 |
25 | Ring Retain 5-8In. .579 Fr.Id | 2 |
26 | Clamp - roller shaft block | 4 |
27 | NLA Roller Assembly Front 600T | 1 |
28 | Spacer front roller mount | 2 |
29 | Bolt 5/16-18X2.25 HXHD GR5 ZN | 2 |
30 | Washer Flat 5-16In. | 3 |
31 | Cover - front end 600T | 1 |
32 | Label 115 Volts | 1 |
32a | Label 220 Volts | 1 |
33 | Switch On-Off | 1 |
34 | Input, Power | 1 |
35 | Plastic T Head Rivet | 3 |
36 | Clip Wire 1-2In.Heavy Duty | 1 |
37 | Clip Wire Latching | 7 |
38 | Cover - Motor 600T | 1 |
39 | Screw | 2 |
40 | Weldment left upright 600T | 1 |
41 | Weldment right upright 600T | 1 |
42 | Screw, Locking | 16 |
43 | Cover plate left upright | 1 |
44 | Cover plate right upright | 1 |
45 | Grip Handlebar | 2 |
46 | Holder User Precautions Label | 1 |
47 | Label user precautions | 1 |
48 | NLA Service kit 600T - Covers H2O | 1 |
49 | NLA Service kit 600T - Covers H2O | 2 |
50 | NLA Cover, Junction, Right | 1 |
51 | Screw | 8 |
52 | NLA Flywheel drive pulley 600T | 1 |
53 | NLA Disc speed sensor | 1 |
54 | Weldment Motor Strap 2.5Hp | 1 |
55 | Pin Motor Strap | 1 |
56 | Pin, Latch | 4 |
57 | Pin clevis 3/8dia X 1-41/64" g | 1 |
58 | Pin clevis 3/8 dia X 2-25/64" | 1 |
59 | Bolt Hex Hd. 5-16-18 X 1In. | 1 |
60 | NLA Weldment tensioner bracket | 1 |
61 | Retainer Drive Belt Tensioner | 1 |
62 | Spring, Tensioner | 2 |
63 | NLA Motor elevation 115volt | 1 |
63a | NLA Motor, Lift | 1 |
64 | Key Ansi Square | 1 |
65 | Screw | 7 |
66 | NLA Bracket - optical speed sensor | 1 |
67 | NLA Opto Sensor Long Cable | 1 |
68 | NLA Washer Flat No. 4 | 1 |
69 | Screw 4-40 x .44 PNHD Phil Plt | 1 |
70 | Wshr Fender 1-4X1.0X.051 | 1 |
71 | Wshr Lock Ex 1-4 Zinc | 1 |
72 | NLA Bolt | 1 |
73 | Screw 3-8-16X3.75 Hex Cap Gr5 | 2 |
74 | Wshr Uss 3-8 Zinc | 4 |
75 | Wheel | 2 |
76 | Nut Lock 3-8-16 Ring Nylon | 3 |
77 | Keps 10-32 Hex Stl Zinc | 2 |
78 | Cap rib-lok SQR 1-1/2-12-14 | 2 |
79 | Holder - Accesory Console 600T | 1 |
80 | Holder - cup - tube mount | 1 |
81 | Pin clevis 3/8 dia X 2-1/64" g | 2 |
82 | Filter, Line | 1 |
83 | NLA Controller, 110V | 1 |
83a | NLA Controller Lower 220V | 1 |
84 | Shield lower controller 600T | 1 |
85 | Clip S-type .090-.130 panel ra | 2 |
86 | Console Top Plastic Tm | 1 |
87 | Console Back Plastic Tm | 1 |
88 | NLA Console, Electronic board, lower | 1 |
89 | Screw | 19 |
90 | Screw | 13 |
91 | Washer No. 8 Ext Znpl | 2 |
92 | Motor, Drive | 1 |
92a | NLA Motor DC 2.5HP 240v | 1 |
93 | NLA Grip, HR, Front | 2 |
94 | NLA Grip, HR, Back | 2 |
95 | NLA Touch pad, Upper | 1 |
96 | NLA Touchpad, Lower | 1 |
97 | Screw | 1 |
98 | NLA Pulley, Idler | 1 |
99 | Pad motor ground isolating | 4 |
100 | Console electronic board | 1 |
101 | Weldment Handlebar 600T | 1 |
102 | Decal Serial Number Cybex | 1 |
103 | Label handlebar mounting instr | 1 |
104 | Keps 8-32 Hex Stl Zinc | 1 |
105 | Screw 8-32 x 1"LG PNHD Phil Bl | 1 |
106 | Spacer round .166ID x .31OD x. | 1 |
107 | Decal Cybex logo 3.12 x 15.11 | 2 |
108 | Weldment Elevation 6XXT | 1 |
109 | Belt, Drive | 1 |
110 | Screw 8-32 X 3-4 Phms Go | 2 |
| HR monitor PCB | 1 |
| Treadmill 110V power cord 12' | 1 |
| Power cord, 220V | 1 |
| NLA Power Cord 220V 50Hz Rt Angle | 1 |
| Safety key | 1 |
| NLA Wire harness | 1 |
| NLA Wire harness | 1 |
| Cable white 1 cond. x 24" | 1 |
| Cable black 1 cond. x 24" | 1 |
| Cable ground 1 cond. x 18" | 1 |
| Cable black 1 cond x 6" | 1 |
| Cable white 1 cond x 6" | 1 |
| Cable 2 cond 2/ferrite 11" | 1 |
| Label Safety Ground | 1 |
| Label StableFlex oval 1.18 x 3 | 1 |
| Label - Caution - Cover Removal | 1 |
| Assembly Polar Pcb Cable S | 1 |